Key Takeaways
- Weight and tire width set the starting pressure. The tool uses Frank Berto's chart for road tires, which gives the pressure that lets the tire sag about 15% of its width under load[1]. For 85 kg of rider, bike and kit on 28 mm tires, that is about 64 psi in front and 78 psi at the back.
- Heavier riders need more pressure and wider tires need less. In the chart, a 25 mm tire needs 88 psi at 200 lb total weight and a 37 mm tire needs 46 psi[1].
- The chart is a starting point, not a measurement of your tires. The 15% figure came from tire makers' advice, not from testing, and tires with supple casings can feel right at other pressures[2]. On rough roads and gravel, lower pressure cut vibration in the one gravel study[4].
- Never go past the lowest maximum pressure printed on your rim or tire. If the rim's maximum is lower than the tire's, the rim's applies[5].
How It Works
A published chart, read for your weight and tire width.
Berto was engineering editor at Bicycling magazine. He measured 50 road tires at seven pressures from 40 to 160 psi and eight loads from 20 to 220 lb, using a hydraulic jack, a bathroom scale and a dial gauge.
For each tire and load he found the pressure that gave a tire drop of about 15% of the tire width[1]. Tire drop is how far the tire sags under the load.
The tool reads that chart. Each line on it is straight, so for a given width the pressure is the printed pressure at 200 lb plus a fixed number of psi for each pound above or below. Between the five widths Berto drew, the tool blends the two nearest lines.
| Measured width | psi at 200 lb | bar | psi per 10 lb |
|---|---|---|---|
| 23 mm | 106 | 7.3 | 5.9 |
| 25 mm | 88 | 6.1 | 5.1 |
| 28 mm | 76 | 5.2 | 4.2 |
| 32 mm | 60 | 4.1 | 3.3 |
| 37 mm | 46 | 3.2 | 2.2 |
The five chart lines the tool uses. The pressure at 200 lb is printed in Berto's article. The slope is read from the chart image and is accurate to a few psi.
Berto also drew 19 and 20 mm lines, which are not used because Heine notes that hardly anybody rides 20 mm tires today[2].
Front and rear. Berto says weight sits about 45% on the front wheel and 55% on the rear for a typical sport tourist riding on the drops. He suggests taking about 10% off the front pressure and adding about 10% to the rear[1].
The tool does exactly that by default. His alternative is a wider tire on the rear at the same pressure.
Worked example: Berto's 170 lb rider on a 30 lb bike, 25 mm tires
Total weight is 200 lb (90.7 kg). The chart gives 88 psi for a 25 mm tire.
Front: 88 × 0.9 = 79 psi (5.4 bar). Rear: 88 × 1.1 = 97 psi (6.7 bar).
In metric, a 75 kg rider with 10 kg of bike and kit on 28 mm tires is 187 lb in total. The chart gives 71 psi, so about 64 psi front and 78 psi rear.
The tool has no input for tubeless, tube type or road surface. The chart has no setting for them, and no source gives a verifiable number, so none is guessed.
Pressure by Weight and Width
Front and rear psi for four total weights, on the default front and rear split.
| Width | 65 kg | 80 kg | 95 kg | 110 kg |
|---|---|---|---|---|
| 23 mm | 65 / 79 | 83 / 101 | 100 / 123 | 118 / 144 |
| 25 mm | 53 / 65 | 68 / 83 | 84 / 102 | 99 / 121 |
| 28 mm | 47 / 58 | 60 / 73 | 72 / 88 | 84 / 103 |
| 32 mm | 37 / 45 | 47 / 57 | 57 / 69 | 67 / 81 |
| 37 mm | 30 / 37 | 37 / 45 | 43 / 53 | 50 / 61 |
Front / rear psi on Berto's chart with the 45/55 split, rounded to the nearest psi. Total weight is rider plus bike and kit.
Read across a row and the pressure climbs with weight. Read down a column and it falls as the tire gets wider. Berto's own conclusion was that most riders under-inflate skinny tires and over-inflate fat ones, and that heavier people should use fatter tires[1].
Where a result falls under about 35 psi, the calculator warns you. In the chart image, the 32 and 37 mm lines stop around 35 psi and the others around 30 psi, so anything lower is a line the tool has extended.
What the Research Says
Where the 15% rule holds up and where it does not.
The 15% is a convention. Jan Heine of Bicycle Quarterly got Berto's original data. He notes that the 15% figure came from the advice of several tire makers, not from testing, and that Berto's chart shows what an average tire from the 1990s needs to reach that drop[2].
He found that supple tires sag more than stiff ones at the same pressure, so a supple tire needs more air to reach 15%. He also says Berto's numbers work quite well for his supple tires on pavement even though they give more than 15% drop[2].
Pressure matters less than people think on smooth roads. Heine's coast-down tests found that two supple 25 mm Vittoria tires, a clincher and a tubular, rolled as fast at 70 psi as at 130 psi[2].
His explanation is that higher pressure cuts the energy lost flexing the tire but adds energy lost to vibration, and the two roughly cancel. These are the magazine's own tests, not a peer-reviewed study. A 2025 lab study found something a little different.
Four riders on a drum treadmill, one tire model in five widths from 23 to 32 mm, got the longest coast-out at pressures higher than usual practice but within the maker's range, and the benefit of going wider levelled off at about 30 mm[3].
The authors warn that their 200 mm drum may deform tires slightly more than a flat road would, so the exact pressures should not be copied to the road. It is a conference abstract.
Rough surfaces favor lower pressure. In a pilot study of nine riders on 45 mm gravel tires, going from 3.5 bar to 1.5 bar cut the resultant vibration at the front dropout by 39% and at the rear dropout by 44%[4].
It was one bike, one gravel road and a short 150 m run at 25 km/h, and it measured vibration, not speed. In the lab study above, higher pressure raised vibration only slightly, and width mattered far more[3].
Heine's advice is to run a low but safe pressure on rough roads[2].
Low pressure has a floor. Berto says under-inflated tires pick up impact punctures, called snakebites, because the tube is pinched against the rim[1].
Heine adds that pressure must be high enough that the tire does not fold under you in hard cornering, and that pinch flats are rare with wide tires[2]. If you flat from pinches, raise the pressure or move to a wider tire.
How to use this
Rim and Tire Maximums
The number on the rim beats the number from any chart.
Berto explains what the maximum on a sidewall means. Tires were mounted on the proper width and type of rim and inflated to twice the listed pressure in a water tank, and none blew off[1].
The key words are proper rim width and type. He also says tires at maximum diameter tolerance on a rim at minimum tolerance may come off below the rated pressure, and that high pressures call for hooked-edge rims[1].
Hookless rims are stricter.
Schwalbe says the rim maximum must be followed when it is lower than the tire's.
It also publishes its own limits for its tubeless tires on hookless rims: 5 bar (72 psi) for 25 to 29 mm, 4.5 bar (65 psi) for 30 to 34 mm and 4 bar (58 psi) for 35 to 39 mm[5].
Those are Schwalbe's in-house test results for its own tires, not an official approval, so check your rim maker's figure. Enter the lowest maximum in the calculator to get a warning when the result is above it.
No single pressure limit applies to every hookless rim and tire width, and Schwalbe's numbers drop for wider tires. Use your rim and tire makers' numbers.
Limits of This Calculator
What the chart does not cover.
Road tires, 23 to 37 mm. That is the part of the chart the tool uses. No published source covers wider tires, so the tool stops at 37 mm instead of extending the lines.
Widths between the lines are interpolated. Berto drew lines for 23, 25, 28, 32 and 37 mm. For 30 mm or 35 mm the tool blends the two nearest lines in a straight line.
That should land within a couple of psi, but it is an estimate by this tool, not something Berto measured.
Not for mountain bikes. Berto says the 15% rule is not valid for mountain bike tires, because their rims are narrower relative to the tire and riders want grip and shock absorption, not low rolling resistance[1].
His separate chart for 26-inch mountain tires shows minimum pressures, not best ones, so it is not used.
Averages, not your tire. Berto's numbers come from tires measured decades ago, and Heine notes that specific tires vary quite a bit from the averages[2]. The slopes in the tool are read from a low-resolution chart image, which adds a few psi of error.
It is fine for a starting point and not for settling a fine argument.
Weight split is typical, not yours. The 45/55 split is Berto's figure for a typical sport tourist on the drops. Your bike, position and load will differ, and the tool does not measure it.
Check your gauge. Berto found most gauges accurate out of the box but reading high as they wear, and a pump gauge that shows 100 psi can be 80 to 90[1]. A cheap hand gauge checked against a new one is worth having.
What this tool does not do
Frequently Asked Questions
Sources & References
- All About Tire Inflation. Berto F. Bicycling magazine article (copy hosted by velonerd.cc) (2006)
- Tire Pressure Take-Home. Heine J. Rene Herse Cycles (2016)
- The Impact of Tyre Width, Pressure and Surface Condition on Rolling Resistance and Vibration Transmission of Bicycle Tyres. Buder J, Fouchard E, Schwanitz S. Journal of Science and Cycling, Science and Cycling Conference Lille 2025 (conference abstract) (2025)
- Gravel Bike Vibrations. Viellehner J, Potthast W. ISBS Proceedings Archive 41(1), article 110 (pilot study) (2023)
- Hookless Rims. Schwalbe. schwalbetires.com technology FAQ

Certified Personal Trainer & Sports Nutritionist
NASM-certified fitness and nutrition coach with over 10 years of hands-on experience helping people build strength, lose fat, and live healthier lives. Specializing in gym-based workouts with a strong focus on lifting technique, biomechanics, and practical exercise science. Through FitLifeRegime, sharing the tools, tips, and insights that have worked for hundreds of clients — helping you start your own fitness journey with confidence and clarity.
Learn more about Manish
NASM Certified
Certified Personal Trainer & Sports Nutritionist from the National Academy of Sports Medicine
Disclaimer: This calculator gives a starting tire pressure from a published chart. It is not a safety rating. Never go above the lowest maximum pressure printed on your rim or tire, and ask a qualified bike mechanic if you are unsure about your setup.