Key Takeaways

  • The tool finds the speed at which your power exactly pays for air drag, rolling resistance, gravity and drivetrain loss, using the equations Martin and colleagues validated against a power meter[1]. With the defaults, 250 W on a flat 40 km takes 1:04:06 at 37.4 km/h, and about 83% of your pedal power goes into the air.
  • CdA is the input you are least likely to know. Changing it by 0.02 m² moves the default 40 km by about 82 seconds, and 10% more power moves it by about 133. Wind tunnels do not agree with each other either: reported drag areas for the same time trial position differ by as much as 40% between studies[8].
  • Wind does not cancel on an out-and-back course. Martin's own example, a 4 m/s wind on a 40 km time trial, turns 60:36 into 63:01[1]. You can pick the same pattern here.
  • Treat the answer as an estimate. No one has tested this exact tool against race results. The model underneath matched measured power to a standard error of 2.7 W when its inputs were measured[1], so most of the error you will see comes from the numbers you type in.

The Model

Power in equals power out, solved for speed.

P × Ec = v × [ ½ρ·CdA·(v + w)² + Crr·m·g·cosθ + m·g·sinθ ] + bearings

bearings = v × (91 + 8.7v) / 1000

P is the power at your cranks, Ec is drivetrain efficiency, v is your ground speed in m/s and w is the headwind. ρ is air density, m is rider plus bike, g is 9.81 and θ is the angle of the road.

The three terms in the bracket are air, tires and gravity. The drivetrain efficiency, Ec = 0.97698, and the wheel bearing term are the ones Martin and colleagues measured and used[1].

I left out two of their terms. Changes in kinetic energy were about 1% of power in their trials, because the riders held a steady speed[1]. Their wheel-spoke drag term is covered here by your CdA, so enter a figure that includes the wheels.

There is no closed-form answer, so the page searches for the speed where the two sides match. Air density is fixed at 1.225 kg/m³, the standard sea-level value. Thinner air at altitude or on a hot day would make you somewhat faster than shown.

Worked example: the default ride

250 W, 75 kg rider, 8 kg bike, CdA 0.3, Crr 0.0042, flat road, no wind. The tool settles on 37.45 km/h. At that speed air takes 207 W, tires 36 W and wheel bearings 1.9 W, and the drivetrain loses 5.8 W.

Together that is your 250 W. Debraux and colleagues put air drag at about 90% of power on level ground above 14 m/s (50 km/h)[5]. Here the share is lower because the speed is lower, and Martin found rolling resistance took a bigger share at low speed[1].

Wind on an Out-and-Back Course

The speed you gain on the way home never pays back what you lose on the way out.

Air drag grows with the square of your speed through the air. A 15 km/h headwind on a rider doing 35 km/h raises the air speed from 35 to 50 km/h, so drag force rises by (50 ÷ 35)² − 1, about 104%.

You will not lose that much speed, because you slow down and the drag settles below it.

Martin and colleagues worked a 40 km out-and-back time trial at 255 W. In calm air the rider holds 11 m/s and finishes in 60:36.

With a 4 m/s wind in one direction, the leg into the wind runs at 8.63 m/s (38:37) and the leg with it at 13.67 m/s (24:24)[1]. The two speeds average 11.15 m/s, but the whole course comes out at 10.58 m/s, so the finish is 63:01[1].

That is 4.0% longer than 60:36 by calculation. The paper itself calls it about 5%. They also found that at 255 W the wind changes your speed by about 62% of the wind speed[1].

As a sanity check, I fed this tool their 255 W, their drag area of 0.264 m² and their Crr of 0.0032, which they took from published tire tests rather than measuring.

The paper gives the riders' mass as 71.9 kg but not the bike's, so this page uses 71.9 kg for the rider and assumes 9 kg for the bike.

It gives 11.06 m/s in calm air, against their 11 m/s, and the 4 m/s out-and-back wind costs 4.0%, against their 63:01 versus 60:36. That checks the maths, not the tool's accuracy on real courses.

WindFinish timeVs calm
Calm1:04:06-
Headwind the whole way1:22:43+1117 s
Tailwind the whole way51:03-783 s
Out and back1:06:53+167 s

Default ride, 40 km flat, 250 W, wind of 14.4 km/h (4 m/s).

On this ride the out-and-back wind costs 4.3%. Real wind shifts in direction and strength along a route, so Steady and Out & back are the two clean cases, not a forecast.

How Hills Are Handled

One grade for every hill, a coast on every descent, and a speed limit you set.

The tool does not read a route file. You give it the distance, the total metres climbed and the total metres lost, and one grade for every hill.

It divides the climbing by the sine of that grade to get the distance spent going up, does the same for the descending, and treats the rest as flat. The flat and the climbs are ridden at your power.

If the climbing and descending do not fit in the distance at your grade, the page says so instead of quietly trimming them.

On descents the tool assumes you coast. Your speed is the one where gravity exactly cancels air drag, rolling resistance and bearing friction, held to the limit you set.

The limit is your call, because corners and braking vary too much to guess. If you would pedal on descents, this tool will not show it.

Worked example: 100 km with 1,200 m of climbing and descending

At 250 W and the default body and bike, the flat 51.9 km goes at 37.4 km/h, the 24.0 km of 5% climbing at 18.0 km/h and the 24.0 km of descending at the 50 km/h limit. Finish: 3:12:06.

Your average power over the whole ride is 212 W, because the descent counts as zero. Losing 3 kg saves 141 s here and only 7 s on the flat 40 km, because weight barely changes air drag.

Real courses go up and down in many small steps, and a tool that reads your route will follow it more closely. Use this one for a quick plan or to compare what-ifs.

Choosing Your Inputs

Power, CdA and Crr do most of the work.

Power. Enter the average you expect to hold for the whole ride. Andrew Coggan, who wrote the TrainingPeaks guide to threshold power, says the most direct estimate of your sustainable power is a time trial of an hour or so[6].

That makes your threshold a fair starting point for a time trial of about an hour and too high for a five-hour ride. The tool does not lower your power as the ride goes on, so account for fatigue yourself.

The Cycling Critical Power Calculator can help you estimate what you can hold for other durations.

CdA. The default of 0.30 m² is a round placeholder, not a measured typical value, so replace it if you can. In Martin's wind tunnel tests, six riders in a time trial position measured between 0.255 and 0.269 m² at the yaw angles they tried[1].

Position and equipment change the number a lot. A review of wind tunnel work reports drag reductions of as much as 15 to 20% going from the hoods to the drops and as much as 30 to 35% going to a time trial position[8].

Another study found the drag area on a time trial bike was 31% higher when five professionals pedalled at race effort than when they held still[4], so a figure measured on a static rider will flatter you. Debraux and colleagues review the methods used to measure drag area[5].

The Cycling CdA Calculator is the place to work out your own figure.

CdAFinish timeSpeed
0.25 m²1:00:3239.6 km/h
0.30 m²1:04:0637.4 km/h
0.35 m²1:07:1735.7 km/h
0.40 m²1:10:1034.2 km/h

Default ride, 40 km flat, 250 W, only CdA changed. The values are examples, not measurements of any rider.

Crr. The default of 0.0042 is the middle road tire in Bicycle Rolling Resistance's drum tests, with the fastest tenth near 0.0029 and the slowest tenth near 0.0057[7]. Drum figures are for smooth pavement, so rough roads cost more.

The Cycling Rolling Resistance Calculator shows how those tire numbers are built.

How Accurate Is It?

The physics is sound. The inputs are the weak point.

Martin and colleagues compared modelled power with an SRM power meter across their road trials. The two averaged 172.8 W measured and 172.0 W modelled, with a standard error of 2.7 W[1].

That is the model under good conditions, with drag area, air density and wind measured. The authors suggest that limits in measuring air density, wind speed and wind direction may have produced much of the remaining variability[1].

Other models have been tested on race times, but they take physiological inputs rather than a power figure. Olds and colleagues predicted 4,000 m pursuit times for 18 track cyclists with a mean difference of 4.6 s, or 1.3%[2].

Their road model predicted a 26 km time trial for 41 cyclists with a mean absolute difference of 3.87%[3]. Those figures do not transfer to this page, but they show what a good model can reach. This tool has no tested accuracy.

What the model leaves out

  • Drafting. A review reports 15 to 50% less drag for a rider right behind another, and 10 to 30% about a bike length back[8]. This tool assumes you ride alone.
  • Changing power. It uses one average for the whole ride, with zero on descents.
  • Braking, corners and stops. Only the descent speed limit stands in for them.
  • Air density other than 1.225 kg/m³, crosswinds and wind that changes along the route.
  • Rough surfaces, which raise rolling resistance.
  • Fatigue and fuelling. Enter the power you can actually hold for the whole ride.

For training load from real ride files, use the Cycling NP, IF and TSS Calculator. For plain speed, time and pace arithmetic on a flat course, there is the Bike Pace Calculator.

Frequently Asked Questions

Sources & References

  1. Validation of a Mathematical Model for Road Cycling Power. Martin JC, Milliken DL, Cobb JE, McFadden KL, Coggan AR. Journal of Applied Biomechanics 14(3):276-291 (1998)
  2. Mathematical model of cycling performance. Olds TS, Norton KI, Craig NP. Journal of Applied Physiology 75(2):730-737 (1993)
  3. Modeling road-cycling performance. Olds TS, Norton KI, Lowe EL, Olive S, Reay F, Ly S. Journal of Applied Physiology 78(4):1596-1611 (1995)
  4. Reference values and improvement of aerodynamic drag in professional cyclists. García-López J, Rodríguez-Marroyo JA, Juneau CE, Peleteiro J, Martínez AC, Villa JG. Journal of Sports Sciences 26(3):277-286 (2008)
  5. Aerodynamic drag in cycling: methods of assessment. Debraux P, Grappe F, Manolova AV, Bertucci W. Sports Biomechanics 10(3):197-218 (2011)
  6. What Is Functional Threshold Power?. Coggan A. TrainingPeaks (page updated May 11, 2026)
  7. Road Bike Tires Test Results (table read 3 November 2026). Bicycle Rolling Resistance. bicyclerollingresistance.com
  8. Riding against the wind: a review of competition cycling aerodynamics. Crouch TN, Burton D, LaBry ZA, Blair KB. Sports Engineering 20:81-110 (2017)
Manish Kumar
Manish Kumar

Certified Personal Trainer & Sports Nutritionist

NASM-CPTCertified Sports Nutritionist10+ Years Experience500+ Clients Coached

NASM-certified fitness and nutrition coach with over 10 years of hands-on experience helping people build strength, lose fat, and live healthier lives. Specializing in gym-based workouts with a strong focus on lifting technique, biomechanics, and practical exercise science. Through FitLifeRegime, sharing the tools, tips, and insights that have worked for hundreds of clients — helping you start your own fitness journey with confidence and clarity.

Learn more about Manish
NASM Certified Personal Trainer Certificate

NASM Certified

Certified Personal Trainer & Sports Nutritionist from the National Academy of Sports Medicine

Disclaimer: This calculator is for informational and personal journaling purposes only. It logs measurements and compares them to published reference values. It is not health, medical, or nutrition advice.