Key Takeaways

  • Normalized power (NP) is a weighted average of your power. It counts hard efforts more than easy ones, so a surgy ride gets a higher NP than a steady ride with the same average[5].
  • Intensity factor (IF) is NP divided by your FTP. Training stress score (TSS) is IF squared times the hours you rode times 100, so one hour at FTP is 100 TSS[2][3].
  • NP is calculated from power recorded second by second, so pasting your power file is the closest this tool gets to what your head unit does. If you only know average power, it gives a range, not a single figure.
  • IF and TSS are only as good as the FTP you enter. If your FTP is out of date, so are the numbers.

How NP, IF and TSS Are Worked Out

Four published formulas, as set out by TrainingPeaks and Dr. Andy Coggan.

MeasureHow it is calculatedBasis
Normalized power (NP)30-second rolling average of power, each value raised to the 4th power, averaged, then the 4th rootTrainingPeaks coach article[5]
Intensity factor (IF)NP / FTPTrainingPeaks[1][3]
Training stress score (TSS)(seconds × NP × IF) / (FTP × 3,600) × 100, which equals IF² × hours × 100TrainingPeaks[2][3]
Variability index (VI)NP / average powerTrainingPeaks Help Center[4]

The formulas this tool uses. Source numbers match the sources list.

The formula for TSS is built so that riding for one hour at your FTP scores exactly 100[2]. Riding at half that intensity for one hour scores 25, because IF is squared.

Worked example: NP given

FTP 250 W, NP 225 W, ride time 90 minutes. IF = 225 / 250 = 0.90. TSS = 0.90² × 1.5 hours × 100 = 121.5.

Worked example: NP from the data

TrainingPeaks' coach article gives a small file: 400 W for 70 seconds, 600 W for 30 seconds, then 400 W for 20 seconds. Its average power is 450 W and TrainingPeaks reports an NP of 478 W[5]. Pasting those 120 values into this tool gives 478 W, a VI of 1.06. That file is far too short for NP to mean much (see the limits below). It is here as a check that the calculation matches.

What the NP Calculation Does

Four steps, applied to power recorded once per second.

  1. Take a rolling average of power over 30 seconds. The first value is the average of the first 30 seconds, then it moves forward one second at a time[5].
  2. Raise each of those averages to the 4th power.
  3. Average all of the results.
  4. Take the 4th root of that average. The answer is NP.

The 4th power gives high values more weight and low values less, so coasting does not drag NP down the way it drags average power down[5].

TrainingPeaks says the 30-second window and the exponent were chosen because physiological responses are not instant and do not rise in a straight line with intensity[5]. When power is perfectly steady, NP equals average power. The method comes from Dr. Coggan's book[5][6].

Dr. Coggan gives a real-world reason for all this: average power is often lower in a criterium than in an equally hard road race, because of the time spent coasting through corners, yet the NP for the two is generally very similar[1].

In the same article, TrainingPeaks says these values were picked to fit a population, and that NP may underestimate the load on someone new to the sport and overestimate it for a very well trained rider[5].

Variability Index: Typical Ranges

NP divided by average power. The higher it is, the more variable the ride.

TrainingPeaks describes VI as the ratio of NP to average power, and says the greater the VI, the more variable and less continuously aerobic the effort[4].

The "Only average power" mode in this tool multiplies your average power by the low and high end of the range for the ride type you pick.

Type of rideVI range
Steady isopower workout (endurance ride)1.00 to 1.02
Flat road race1.00 to 1.06
Flat time trial1.00 to 1.04
Hill-climb time trial1.00 to 1.06
Flat criterium1.06 to 1.35
Hilly criterium1.13 to 1.50
Hilly road race1.20 to 1.35
Mountain bike or cyclocross race1.13 to 1.50

Variability index for common rides, as published by TrainingPeaks.

These are typical ranges, not limits. A ride can fall outside its row, which is why the tool shows a range and not one number.

Reading Your IF and TSS

Published reference values. They describe typical sessions and are approximate.

IFTypical for
Under 0.75Recovery rides
0.75 to 0.85Endurance-paced training rides
0.85 to 0.95Tempo rides, aerobic and anaerobic interval workouts (work and rest combined), longer road races (over 2.5 h)
0.95 to 1.05Lactate threshold intervals (work period only), shorter road races (under 2.5 h), criteriums, circuit races, longer time trials (such as 40 km)
1.05 to 1.15Shorter time trials (such as 15 km), track points race
Over 1.15Prologue time trial, track pursuit, track miss-and-out

Typical IF values for different sessions or races (TrainingPeaks, Coggan).

One note from the same source: an IF above 1.05 in a race of about an hour often means the threshold power you entered is lower than your real one[1].

TSS for a rideLevelWhat TrainingPeaks says
Under 150LowRecovery generally complete by the following day
150 to 300MediumSome residual fatigue may be present the next day, but gone by the 2nd day
300 to 450HighSome residual fatigue may be present even after 2 days
Over 450Very highResidual fatigue lasting several days likely

TSS as an approximate guide to recovery (TrainingPeaks, Coggan).

Recovery depends on much more than one number: sleep, food, the rest of your week and how you feel. Use the scale as a rough guide and let how you feel overrule it.

What It Cannot Tell You

Some limits worth knowing before you lean on the numbers.

  • Your FTP drives everything. IF and TSS are NP measured against the FTP you type in. A wrong FTP gives wrong IF and TSS, even if NP is right. To find yours, try the FTP Calculator.
  • Short rides. TrainingPeaks says to ignore NP for periods under roughly 10 minutes, because the 30-second rolling average takes up too much of the period[3][5]. This tool warns you when your ride is shorter.
  • Steady efforts. TrainingPeaks' coach article says average power is more appropriate than NP on long climbs and in time trials, and that NP should not be used to judge performance[5].
  • Estimates from average power. Average power alone cannot tell you how much your effort varied. The range this tool gives is based on typical VI values, and your ride may differ.
  • Data handling. This tool treats every pasted value as one second and counts zeros as zeros. Head units and training sites may treat pauses and dropouts differently, and their methods are not all published, so your figure may differ slightly from theirs.
  • What TSS measures. TrainingPeaks says TSS was modelled after Dr. Eric Bannister's heart-rate-based training impulse (TRIMP), and suggests it may be best viewed as a predictor of the glycogen used[1]. No independent research tests that claim, so treat TSS as a useful bookkeeping number and not a lab measurement.
  • Tool limits. The tool accepts an FTP of 50 to 600 W, ride times of 1 minute to 24 hours (30 seconds to 24 hours of pasted data) and a VI of 1.00 to 2.00. Those are limits of this tool, not published rules.

Normalized Power, NP, Intensity Factor, IF, Training Stress Score and TSS are marks of TrainingPeaks, LLC. This page is not affiliated with or endorsed by TrainingPeaks. It uses the published calculations.

Frequently Asked Questions

Sources & References

  1. Normalized Power, Intensity Factor and Training Stress Score. Coggan A. TrainingPeaks Learn (updated 11 May 2026)
  2. Estimating Training Stress Score (TSS). Friel J. TrainingPeaks Learn (updated 13 April 2026)
  3. Normalized Power. TrainingPeaks. TrainingPeaks Help Center
  4. Variability Index (VI). TrainingPeaks. TrainingPeaks Help Center
  5. Understanding Normalized Power Calculations to Coach Cyclists. Epton T. TrainingPeaks Coach Blog (updated 15 October 2024)
  6. Training and Racing with a Power Meter, 3rd edition. Allen H, Coggan AR, McGregor S. VeloPress (2019)
Manish Kumar
Manish Kumar

Certified Personal Trainer & Sports Nutritionist

NASM-CPTCertified Sports Nutritionist10+ Years Experience500+ Clients Coached

NASM-certified fitness and nutrition coach with over 10 years of hands-on experience helping people build strength, lose fat, and live healthier lives. Specializing in gym-based workouts with a strong focus on lifting technique, biomechanics, and practical exercise science. Through FitLifeRegime, sharing the tools, tips, and insights that have worked for hundreds of clients — helping you start your own fitness journey with confidence and clarity.

Learn more about Manish
NASM Certified Personal Trainer Certificate

NASM Certified

Certified Personal Trainer & Sports Nutritionist from the National Academy of Sports Medicine

Disclaimer: This calculator is for informational and personal journaling purposes only. It logs measurements and compares them to published reference values. It is not health, medical, or nutrition advice.